how wide is the discharge por Tof the jaw crusher

    • Method for adjusting the discharge particle size of jaw ...

      2021-8-9 · The adjustment device of the jaw crusher is an adjustment mechanism for the size of the discharge port of the rock crusher. With the operation of the equipment, the wear of the crushing tooth plate increases, and the discharge port gradually increases, and the size of the crushed product continues to become coarser. In order to ensure For product particle size requirements, an adjustment ...

    • Jaw Crusher VS Cone Crusher | Which Is The Better Crusher | …

      Jaw Crusher Working Principle

    • How to Adjust the Size of the Product Granularity of Jaw ...

      2018-11-26 · 2018-11-26 · In order to make the size of the product small, it is necessary to adjust the size of the jaw crusher outlet. There are three ways to adjust the discharge port of the jaw crusher. The first type and gasket adjustment: open the adjustment seat with the top bolt, and check or remove the back wall support and the rear wall of the frame.

    • Adjusting Measures of the Jaw Crusher Outlet

      2017-9-26 · III. Support device adjustment. It refers to the bearing part of the jaw crusher, which is generally used for sliding bearing with babbitt alloy. It can withstand large impact load and is more durable. However, when it is inefficient, it needs to be forced to lubricate. IV. Wedge adjustment. It is the relative movement of the two wedges between the rear thrust plate support and the back wall of the rack to realize the adjustment of the crusher …

    • How to Adjust The Width of The Discharge Port of Jaw ...

      2016-9-27 · Add a set of equal thickness gaskets between the rear thrust plate bearing and the rear wall of the frame. The purpose is to increase and decrease the discharge of the jaw crusher by increasing or decreasing the number of gaskets. This method is very suitable for large and medium-sized jaw crusher. 2 hydraulic adjustment

    • Adjustment method of jaw crusher discharge port_The NIle ...

      2021-9-16 · During the use of the jaw crusher, our customers often feedback some of these or those problems to us.Among them, the most consulted is the adjustment method of the jaw crusher''s discharge port. Today, the editor will take you to understand how to adjust the discharge port of the jaw stone crusher.

    • TECHNICAL SPECIFICATIONS QJ241 JAW CRUSHER

      QJ241 JAW CRUSHER ENGINEERING IN MOTION QJ241 JAW CRUSHER KEY SPECIFICATIONS DATA Equipment Single toggle C10 jaw crusher Feed opening 1000 mm x 650 mm / 40" x 26" Optimum feed size 520 mm3 / 21 inch3 Engine C7.1 Acert 168 kW / 225 hp Transport dimensions 13.90 m / 45'' 7 ⅜" (l) 2.64 m / 8'' 7 ⅞" (w) 3.22 m / 10'' 6 ⅝" (h)

    • Method for adjusting the discharge particle size of jaw ...

      2021-8-10 · The adjustment device of the jaw crusher is an adjustment mechanism for the size of the discharge port of the rock crusher. With the operation of the equipment, the wear of the crushing tooth plate increases, and the discharge port gradually increases, and the size of the crushed product continues to become coarser.

    • How to adjust the CSS of Jaw Crusher?

      2021-4-8 · The discharging port of the jaw crusher can be adjusted according to the needs of customers. How to adjust the CSS of jaw crusher? First, the width of the discharge port is adjusted and set with the backing plate. The principle of action is to put a group of adjusting pads behind the …

    • Adjusting Measures of the Jaw Crusher Outlet

      2017-9-26 · Jaw crusher is widely used in mining, metallurgy, building materials, highway, water conservancy and chemical industries. In usual, it takes a month or so to readjust the discharge port. Here are the adjustment measures of jaw crusher outlet.

    • Jaw Crusher Working Principle

      – 800 mm / 31 ½ " wide conveyor with a discharge height of 3444 mm / 11'' 3 ⅝" – Hydraulic raise / lower facility to give increased clearance for rebar discharge in recycling applications – Tunnel arrangement to reduce catchment points in recycled materials – Speed wheel fitted to …

    • How to Adjust The Width of The Discharge Port of Jaw ...

      2016-9-27 · Jaw crusher for stone breaking, also known as the tiger mouth, which crushing cavity composed of mobile jaw and static jaw simulates movement of animal jaw to complete the crushing operation. Because that the structure of the jaw crusher for stone breaking has the advantages of simple and convenient operation, work reliability, convenient maintenance, so it has been welcomed in …

    • How to Adjust the Size of the Product Granularity of Jaw ...

      2018-11-26 · In order to make the size of the product small, it is necessary to adjust the size of the jaw crusher outlet. There are three ways to adjust the discharge port of the jaw crusher. The first type and gasket adjustment: open the adjustment seat with the top bolt, and check or remove the back wall support and the rear wall of the frame.

    • Inlet and Discharging Port of Five Crushers

      2019-11-21 · The jaw crusher is mainly used for medium-sized crushing of various ores and bulk materials and can crush materials with compressive strength of not more than 320Mpa, which are divided into coarse and fine broken. The series of products are complete in specifications, and the feed size is 125mm ~ 750mm, which is the primary crushing equipment.

    • How to adjust the CSS of Jaw Crusher?

      2021-4-8 · Jaw crusher, as a common crusher equipment, occupies an important position in the crusher industry. Jaw crusher has the characteristics of large crushing ratio, good performance and high efficiency. The discharging port of the jaw crusher can be adjusted according to the needs of customers. How to adjust the CSS of jaw crusher? First, the width of the discharge port is adjusted and set with …

    • Method for adjusting the discharge particle size of jaw ...

      2021-8-9 · Phone: +0086-371-67660555, Whatsapp/Wechat: +0086-13676922906, Email: [email protected] . Leave Message Chat Online. AddThis Utility Frame. The adjustment device of the jaw crusher is an adjustment mechanism for the size of the discharge port of the rock crusher.

    • Inlet and Discharging Port of Five Crushers

      2019-11-21 · Hydraulic cylinder way. The hydraulic cylinder discharge port of HD jaw crushers Hydraulic cylinder discharge port is just like a large oil cylinder in the middle of the bracket so that the length of the bracket becomes a step-less adjustment change, thereby changing the front and rear position of the moving jaw to realize the row adjustment of the size of the material.

    • How to adjust the discharge opening of the jaw crusher ...

      2021-3-16 · Jaw crusher is a kind of commonly used crushing equipment. In the process of long-term use, the crushing tooth plate is constantly worn out, the discharge port gradually increases, and the size of the crushed product continues to become coarser. Therefore

    • Inlet and Discharging Port of Five Crushers

      2019-11-21 · The series of products are complete in specifications, and the feed size is 125mm ~ 750mm, which is the primary crushing equipment. At present, the discharge port adjustment methods of jaw crushers with different structures are also different, mainly divided into three types: gasket type, wedge type, and cylinder type.

    • How to adjust the discharge opening of the jaw crusher ...

      2021-3-16 · In the process of long-term use, the crushing tooth plate is constantly worn out, the discharge port gradu y increases, and the size of the crushed product continues to become coarser. Therefore, in order to ensure that the product particle size can meet customer requirements, we need to adjust the size of the discharge opening, so how to adjust ...

Copyright © AMC

gotop